SS621E Silicone Structural Sealant
SS621E Silicone Structural Sealant is a one-component neutral-curing silicone sealant designed specifically for structural bonding applications of dual glass PV modules and solar PV curtain wall engineering. SS621E meets global standards for structural glazing, withexcellent structural adhesion properties and weather resistance.
◆ Odorless, non-corrosive cure system
◆ Excellent weatherability and high resistance to ultraviolet radiation, heat and humidity, ozone and temperature extremes
◆ Remains flexible over a temperature range of -58℉(-50℃)to 302℉(150℃)
◆ Excellent unprimed adhesion to wide range of substrates including coated, enameled, and reflective glasses; anodized and polyester coated or painted aluminum profiles
◆ Dual glass PV modules and solar PV curtain wall engineering
◆ Silicone structural glazing and protective glazing applications
|Tack-free Time(23°C/73°F,50% RH),min
|Durometer Hardness,Shore A
Specifications: Typical property data values should not be used as specifications.
◆ GB 16776/Chinese
◆ ASTMC 1184/America
◆ ETAG 002/European
Clean all joints and glazing pockets, removing all foreign matter and contaminants such as grease, oil, dust, water, frost, surface dirt, old sealants, or glazing compounds and protective coatings.
PROCESSING AND CURING:
Install back-up material or joint filler, setting blocks, spacer shims, and tapes. Mask areas adjacent to joints to ensure neat sealant lines. Primer is generally not required on non-porous surfaces, but may be necessary for optimal sealing of certain porous surfaces. A test placement is always recommended.
Apply SS621E Silicone Structural Sealant in a continuous operation using a positive pressure.(The sealant can be applied using many types of air-operated guns and most types of bulk dispensing equipment.)Before a skin forms(typically within 20 minutes), tool the sealant with light pressure to spread the sealant against the backing material and joint surfaces. Remove masking tape as soon as the bead is tooled.
SS621E Silicone Structural Sealant should not be applied:
◆ To building materials that bleed oils, plasticizers, or solvents– materials such as impregnated wood, oil-based caulks, green or partially vulcanized rubber gaskets or tapes
◆ In totally confined spaces as the sealant requires atmospheric moisture for cure
◆ When surface temperatures exceed 60°C(140°F)
◆ Where painting of the sealant is required, as the paint film may crack and peel
◆ To surfaces in contact with food- this sealant does not comply with Federal Food and Drug Administration food-additive regulations
◆ In below-grade applications
◆ For use as an interior penetration fire stop sealing system
◆ In horizontal floor joints where abrasion and physical abuse are likely to be encountered
◆ To frost-laden or damp surfaces
◆ For continuous immersion in water
SS621E Silicone Structural Sealant is available in 10.1 fl. oz.(300 ml)plastic caulking cartridges and 20 fl. oz.(590 ml)foil sausage packs.
USABLE LIFE AND STORAGE
When stored at or below 27ºC(80ºF)in the original unopened containers, this product has a usable life of 6 months from the date of manufacture.
HANDLING AND SAFETY
PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND MATERIAL SAFETY DATA SHEETS AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD INFORMATION. THE MATERIAL SAFETY DATA SHEET IS AVAILABLE FROM BAIYUN SALES APPLICATION ENGINEER, OR DISTRIBUTOR, OR BY CALLING BAIYUN CUSTOMER SERVICE.
The values in this document are not of all specifications and are subject to change without notice. As the actual situation is very different, it’s hard to guarantee the correctness and applicability of our products in some usage. Users should understand the product before using, and then decide the best way to use it.